Quick answer: To evaluate organobentonite in oil-based drilling fluids, test it in the complete mud formulation and compare the results with a defined control. Review rheology, gel recovery, solids suspension, filtration and stability after aging under conditions relevant to the job. A grade or dosage should not be judged from a powder test alone.
What performance should an evaluation measure?
Organobentonite is used as a rheology modifier in oil-based mud (OBM) and water-in-oil drilling fluids. Its organophilic clay structure can build viscosity and gel strength in compatible oil phases, helping the fluid suspend weighting material and drilled solids. The response depends on the base oil, emulsifier package, solids loading, water phase, mixing energy, temperature history and selected grade.
| Evaluation area | What to record | Why it matters |
|---|---|---|
| Rheology | Viscometer readings across relevant shear rates; calculated PV and YP where used | Shows viscosity profile and low-shear carrying potential |
| Gel behavior | Initial and time-based gel strengths after static rest | Indicates structure recovery and the ability to hold solids between circulation periods |
| Suspension and sag | Density or solids differences between sampled fluid sections after a defined static or dynamic test | Assesses weighting-material settling under the test conditions |
| Filtration | Fluid loss and filter-cake observations using the specified pressure and temperature | Checks the finished mud’s filtration response, not just the clay additive |
| Emulsion and aging stability | Electrical stability where applicable, plus rheology and filtration before and after aging | Separates short-term activation from performance retained after heat and time |
Build a controlled test plan
- Define the fluid: Record base-oil type, oil-to-water ratio, brine composition, emulsifier and wetting agents, weighting material, solids, density, and existing additives.
- Select a control: Prepare the current formulation without the candidate change, or use the existing treatment as the comparison baseline. Keep all non-test variables constant.
- Confirm grade instructions: Review the current grade-specific TDS for compatibility, addition order, shear and any activation requirement. Oil type can change the treatment needed.
- Prepare repeatable samples: Use the same batch size, equipment, mixing sequence and conditioning history. Record actual mixing time, temperature and aging conditions.
- Measure at useful stages: Record initial readings, post-conditioning readings, and measurements after hot rolling or other agreed aging that reflects the service envelope.
- Repeat and document: Run replicate samples where practical, record instrument and test conditions, and report raw results alongside calculated values.
Interpret results as a balance
A higher viscosity or gel value is not automatically a better result. The formulation must balance suspension with pumpability and pressure loss, while meeting filtration and emulsion requirements. Review PV, YP, low-shear readings, gel profile and sag response together. If PV rises sharply, investigate over-treatment, poor dispersion or excess solids before increasing the organobentonite dose.
Use the applicable current oil-based drilling-fluid test procedure agreed with the operator or laboratory. API RP 13B-2 is a recognized reference for field testing oil-based drilling fluids; the test report should identify the procedure and all deviations. Do not compare results from different methods or conditioning histories as if they were equivalent.
Common evaluation errors
- Comparing samples made with different base oils, water ratios or emulsifier packages.
- Using only as-mixed viscosity and skipping static gel or aging measurements.
- Changing clay dosage, activator and mixing energy in the same test, so the cause of the result is unclear.
- Applying one treatment level to diesel, mineral-oil and synthetic-oil systems without formulation trials.
- Using a target from another mud design instead of the operator’s approved specification.
Frequently asked questions
Which properties should I test first?
Start with rheology across relevant shear rates, initial and time-based gels, suspension or sag behavior, and fluid loss. Add emulsion stability and aged-fluid tests when they are part of the mud program.
Can a supplier TDS predict finished-mud performance?
A TDS helps screen a grade and follow its handling guidance. Finished-fluid performance depends on the full formulation and processing conditions, so confirm it in a controlled mud test.
Should organobentonite dosage be the same for every base oil?
No. Base-oil type and formulation polarity affect dispersion and rheology development. Follow grade-specific guidance and establish the treatment level through trials.
What information should I include in a sample request?
Share the base oil, oil-to-water ratio, mud density, emulsifier package, current rheology, target properties, aging conditions and the operator’s acceptance tests.
Need an organobentonite candidate for an OBM trial? Contact Camp-Shinning with your fluid details. Review the oil-based drilling fluid viscosifier overview and our organobentonite product information.